How To Repair A 6 Foot Vinyl Fence

Download Article

Vinyl fences are very resilient, so they don't require a lot of maintenance. If some part does break, your fence is too easy to take apart and reassemble. The virtually difficult task is finding an identical replacement piece. Once yous take it, yous can speedily connect it to the existing parts. Your repaired fence can then serve every bit a characteristic of your domicile for many years.

Things You lot Should Know

If a panel breaks on your vinyl fence, simply remove the top runway and panel from the section you desire to replace, slide the new panels into place, and supercede the rail.
You tin can also replace the runway by cutting it to length, removing the damaged rail, and sliding the new rail into the holes on the debate post.
If ane of the posts gets damaged, unscrew the pinnacle runway, dig upwards the damaged post, set the new post in place with concrete, and reattach the rails and panels.

one
Guild similar replacement panels. You can search online to detect many different fence styles. If yous tin, contact the fence'southward manufacturer to become new panels identical to the onetime ones. Have a picture of your argue and transport it to companies to ensure you get the right panels.^[ane]
- Try to go replacement parts that are the same size and look as shut every bit possible to the residue of your debate.
- Home improvement stores may also sell fence parts and repair kits.
two
Unscrew the top track at the ends. The top rails attaches to the closest posts. Look for a pair of screws at the ends, securing the rail to those posts. Turn the screws counterclockwise to remove them, and so set them aside.^[2]
- These screws may be underneath the caps on the posts. Gently lift them with a hammer and chisel if you can't remove them by hand.
- Keep the screws in a safe spot, such as a airtight container, and so they tin can be reused later.
Advertisement
3
Remove the screws from the damaged panels. Now that the rail is free, locate the screws on the panels. If your fence's panels accept pickets, or vertical bars, behind them, the screws may be at the panel's ends. Turn them counterclockwise to remove them.^[iii]
- Not all fences have pickets or screws. Your fence'due south panels may be held in place with brackets, which you can slide the panels out of.
4
Slide the panels out of the fence. Lift the top rail off of the panel you need to replace. Then, pull the console up to remove it. If you took off all of the screws earlier, the console should come off of the debate easily.^[four]
- If the panel is next to a post, information technology may be attached with side brackets. Carefully move the panel to the side and out of the brackets.
5
Bank check the alignment of the posts with a level. Earlier installing the new panels, make sure the fence posts are level. Hold a level against the side of each connecting post. If a post is positioned correctly, the level volition be announced flat from elevation to bottom. Straighten the posts as needed.^[five]
- If your posts are held in the footing with concrete, they most likely will not demand to be adjusted.
six
Slide the new panels into the fence. Fit each panel over the bottom track. Adjust the panels carefully so each is level from top to bottom. Slide them into whatsoever nearby brackets, so place the top rail over them. Make sure each panel looks evenly spaced in the contend.^[6]
- In most fences, the panels volition fit correct next to each other without leaving a gap.
seven
Screw the panels and top track in place. Look for the screw holes in the top and bottom ends of each panel. Utilize these to fasten the panels to the stabilizing pickets, if your fence has them. Finish adjusting the top rail, then tighten the screws well-nigh the fence posts to secure it in place.^[7]
- If the screw holes do not line upwards, yous can make full the existing panel holes with spray foam, so drill new holes 1 in (two.5 cm) deep.
Advert

ane

Remove the panels from the rails. If your fence's panels fasten to pickets, remove the screws at the top and bottom of the panels get-go. Then, slide the panels out of the track. Clear the track completely.^[8]
2
Unscrew the rail from the posts. Each rail slides into holes on the posts. You will detect a pair of screws property the rails in position. Turn these counterclockwise and fix them aside. Then, slide the rail off of the posts.^[ix]
- Store the screws in a safe location and proceed the old rails in case you need to measure them.
3
Measure the length of rail you demand. Yous can practise this by running tape measure from 1 mail service to another. Recall that each runway needs to have a little extra length in order to slide into the post holes. Add about two in (5.ane cm) onto the length.^[ten]
- If yous have the one-time rail, you can too measure it for utilise as an gauge.
four
Vesture safety goggles and other protective gear. Before sawing into the rails, take the proper safety precautions. Shield your optics from debris by wearing safety goggles. Cover your oral fissure by wearing a respirator.
- Avoid wearing loose clothing or jewelry when operating a saw.
five
Cutting the rail to length with a circular saw. Set the new track on a workbench. Before cutting, marking where you need to brand the cuts then you get the size of runway you need. Then, carefully cut through the rail.^[11]
- For the best results, choose a saw blade labeled for vinyl cutting. Argue companies and home improvement stores may sell these blades.
6
Slide the rail into the holes on the fence posts. Make certain the brackets for the panels are on the summit side. Push button the rail into the post holes until the rail hangs in place. As long every bit the rail is the right length, it should fit.^[12]
- If the rail doesn't fit properly, cheque the length again. Y'all may demand to cut it a little shorter.
7
Screw the rail to the posts. Locate the spiral holes on either end of the runway. Y'all will need a pair of screws on each side. Twist them clockwise to lock the rails in identify. When y'all're done, you lot tin begin installing the vinyl panels.^[thirteen]
- The size of screws yous need differ from rails to rail.
- Screws are usually included with new rails, just you can try using the screws from the one-time runway.
Advertizing

1
Unscrew the connecting rails. Each rail slides into slots on the post and is held in place with screws. Turn the screws counterclockwise to remove them. Pull both the top and bottom runway away from the mail service.^[14]
- If you take trouble installing a post, removing the rails and argue panels completely can give you more space.
two
Dig out the damaged post. Remove the former mail every bit well as any fragments that may be in the ground. If your post was held in place with concrete, you will need to dig up the concrete to remove it.^[15]
- To remove the concrete, dig out the dirt around it. You can refill the hole later.
three
Measure out where the new post will exist placed. To effigy out where to place the new postal service, measure the distance between 2 existing posts. The new post should be placed an equal distance from the concluding mail service. Mark the location with pigment, tape, or another indicator.^[xvi]
- The mail needs to be even and directly or else the rail and panels will not fit correctly.
4

Dig a hole three ft (0.91 m) deep in the ground. Dig out the spot y'all marked earlier. Brand the hole about 8 in (xx cm) in diameter. You can use a tape measure to ensure the hole is the size you demand.
5
Seal the pole in place with physical. You will need about 120 lb (54 kg) of premixed physical for 1 mail service. Place the mail in the hole. While someone holds the postal service in position, fill the the hole with concrete. Pour the concrete until it is about 4 in (x cm) below the basis'southward surface.^[17]
- The other person should concord the mail service straight. If it doesn't look right, conform information technology quickly before the physical solidifies.
6

Reinstall the fence rails and panels. Fit the debate rails into the holes on the new post, then begin sliding the panels onto the rails. Screw the rail to the inside of the post. So, adhere the panels, screwing them in place if they likewise use screws.^[18]

Advertisement

Add together New Question

Question

How tin I repair a break in one of the panels on my fence?

Ryaan Tuttle is a Home Improvement Specialist and the CEO of Best Handyman Boston. With over fifteen years of experience, Ryaan specializes in abode improvement and property maintenance past leveraging technology and adroitness. Ryaan holds his Construction Supervisor and Abode Improvement Contractor Licenses. Unlike almost handyman contractors, Best Handyman Boston is licensed and insured. Boston Magazine and LocalBest.com take named Best Handyman Boston the Best Handyman in Boston.

Dwelling house Comeback Specialist

Practiced Answer

You really would want to try to remove any panel that is. Whatever repair that you would make to information technology would be temporary, and it would just break again over time. You could endeavor gluing information technology, but really it should be replaced if possible.

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Keep whatsoever extra panels you accept later on installing your debate.
There are many different vinyl fence styles, so finding the correct parts can take some time and patience.
Accept a picture of your debate so y'all can get the correct replacement parts.
To keep your vinyl fence in good shape, you'll likely need to clean it approximately in one case or twice a year in addition to making any needed repairs.