banner



How To Repair Pull Chain On Ceiling Fan

Introduction

This guide will show you how to replace a ceiling fan pull concatenation switch.

Ceiling fan pull bondage can break in 2 unlike means:

  1. Chain breaks somewhere in the eye, outside the fan housing
    • In this case, the chain tin be fixed by adding an extension chain.
  2. Chain breaks inside the fan housing
    • The chain will not be visible from the exterior, so the fan housing must be opened to supersede the chain or the pull chain switch itself.

This is a guide for replacing the pull chain switch.

Alert: Following this guide may betrayal you to voltage. Turn off the power from the circuit breaker and turn off any low-cal switches that provide ability to the ceiling fan to forbid injury.

Parts

  1. Caution: Turn off the power from the circuit breaker and turn off any light switches that provide power to the ceiling fan. Remove the white cover by unscrewing the nut on the bottom from where the chain is hanging.

    • Circumspection: Turn off the power from the excursion breaker and turn off any light switches that provide power to the ceiling fan.

    • Remove the white cover by unscrewing the nut on the bottom from where the chain is hanging.

  2. Caution: Let the bulbs cool off before you remove them. Remove the bulbs from their sockets. Remove the bulbs from their sockets.

    • Caution: Let the bulbs absurd off before yous remove them.

    • Remove the bulbs from their sockets.

  3. Remove the screws around the base. Remove the fan housing.

    • Remove the screws around the base of operations.

    • Remove the fan housing.

  4. Pull the switch out of the fan housing,   leaving the wires attached.

    • Pull the switch out of the fan housing, leaving the wires attached.

  5. Cut the colored wires from the switch using a pair of wire cutters. On some switch models, the wires can be detached by pulling. On some switch models, the wires can be detached by pulling.

    • Cut the colored wires from the switch using a pair of wire cutters.

    • On some switch models, the wires tin be detached past pulling.

  6. Note the wire colors and the terminal they attach to on the old switch. 1 - Red 2 - Purple

    • Note the wire colors and the concluding they attach to on the old switch.

    • 1 - Red

    • ii - Purple

    • 3 - Xanthous

    • L - Blackness

  7. Attach the colored wires to the new switch's respective terminals.

    • Adhere the colored wires to the new switch's respective terminals.

  8. Put back the switch in the hole in the fan housing from the inside. Tighten up the screws on the outside.

    • Put back the switch in the pigsty in the fan housing from the within.

    • Tighten up the screws on the outside.

  9. Put back the white cover and then tighten up the nut at the bottom of the cover from where the chain is hanging. Put back the white cover and then tighten up the nut at the bottom of the cover from where the chain is hanging. Put back the white cover and then tighten up the nut at the bottom of the cover from where the chain is hanging.

    • Put dorsum the white cover and and then tighten upward the nut at the bottom of the cover from where the chain is hanging.

  10. Turn the power back on and test the switch to find if it is working or not. Turn the power back on and test the switch to find if it is working or not.

    • Plow the power back on and examination the switch to find if information technology is working or not.

Team

0 Comments

Source: https://www.ifixit.com/Guide/Ceiling+Fan+Pull+Chain+Switch+Replacement/141326

Posted by: reidfromment1969.blogspot.com

0 Response to "How To Repair Pull Chain On Ceiling Fan"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel